It is currently Mon Mar 18, 2024 9:19 pm

All times are UTC - 6 hours





Post new topic Reply to topic  [ 9 posts ] 
Author Message
 Post subject: Engine Cover Hatch Screws Stripping
PostPosted: Wed Sep 27, 2017 6:54 am 
Offline
Newbie

Joined: Mon Sep 04, 2017 7:35 pm
Posts: 22
My 2014 A20 just lost several screws on the piano hinge that holds the engine hatch on.

The design looks pretty awful as the hydraulic opening arm is very powerful, the engine hatch rubs against the hull pretty hard when opened, and the cup holder vinyl is worn off because of friction of the hatch fitting down.

Has anyone seen an updated or better designed hinge? Has anyone switched to a less powerful lifting arm?

_________________
2014 Axis A20 Surf Gate


Top
 Profile  
 
 Post subject: Re: Engine Cover Hatch Screws Stripping
PostPosted: Wed Sep 27, 2017 9:36 pm 
Offline
Team Axis

Joined: Sat Jun 06, 2015 10:35 pm
Posts: 1181
Location: Sammamish WA
My hydraulic arm had come loose from where it mounts to boat.. stripped out :(

Sent from my SM-G955U using Tapatalk

_________________
-2015 A24 - 409 HP - 2249 Prop - 1100 rear sacs - 950 front sac - 290lb rider with Red Rocket and Phase 5 Quest


Top
 Profile  
 
 Post subject: Re: Engine Cover Hatch Screws Stripping
PostPosted: Thu Nov 30, 2017 4:41 pm 
Offline
Newbie
User avatar

Joined: Sun Aug 02, 2015 6:49 pm
Posts: 21
Location: Conroe, TX
I had the exact same problem. Just get a thread repair kit and follow the instructions. I used a recoil thread repair kit and it worked like a champ.


Attachments:
recoil.jpg
recoil.jpg [ 76.96 KiB | Viewed 27399 times ]

_________________
2015 A22
Top
 Profile  
 
 Post subject: Re: Engine Cover Hatch Screws Stripping
PostPosted: Thu Nov 30, 2017 11:51 pm 
Offline
Team Axis

Joined: Sat Jun 06, 2015 10:35 pm
Posts: 1181
Location: Sammamish WA
SweetLily wrote:
I had the exact same problem. Just get a thread repair kit and follow the instructions. I used a recoil thread repair kit and it worked like a champ.
That's the plan! Thanks

Sent from my SM-G955U using Tapatalk

_________________
-2015 A24 - 409 HP - 2249 Prop - 1100 rear sacs - 950 front sac - 290lb rider with Red Rocket and Phase 5 Quest


Top
 Profile  
 
 Post subject: Re: Engine Cover Hatch Screws Stripping
PostPosted: Fri Dec 01, 2017 9:17 am 
Offline
Site Admin
User avatar

Joined: Wed Apr 21, 2010 9:00 am
Posts: 1107
Good tip.


Top
 Profile  
 
 Post subject: Re: Engine Cover Hatch Screws Stripping
PostPosted: Fri Dec 01, 2017 8:47 pm 
Offline
Team Axis

Joined: Sat Jun 06, 2015 10:35 pm
Posts: 1181
Location: Sammamish WA
admin wrote:
Good tip.
I agree! I could not come up with an easy fix but this looks like it!

Sent from my SM-G955U using Tapatalk

_________________
-2015 A24 - 409 HP - 2249 Prop - 1100 rear sacs - 950 front sac - 290lb rider with Red Rocket and Phase 5 Quest


Top
 Profile  
 
 Post subject: Re: Engine Cover Hatch Screws Stripping
PostPosted: Mon Dec 04, 2017 10:07 pm 
Offline
Newbie

Joined: Mon Sep 04, 2017 7:35 pm
Posts: 22
I ended up using zinc drywall anchors on the engine hatch. Can't see it and the larger diameter bites really well in the softer
/loose seat base material.

_________________
2014 Axis A20 Surf Gate


Top
 Profile  
 
 Post subject: Re: Engine Cover Hatch Screws Stripping
PostPosted: Sat Dec 09, 2017 8:45 am 
Offline
Team Axis

Joined: Tue May 24, 2016 7:44 am
Posts: 149
I have Exact same A20 very lightly appointed; I noticed that early on luckily when I noticed it wasn’t quite closing properly and now every 6 months I need to tighten screws , got lucky 1st time had only 1loose/stripped screw and got it to re bite on an angle.

I’m also more careful now and lift slowly till it gets to the last couple inches that the arm takes control. Just regightened them last week cause I noticed the one side closing funny

Wish I would have known about tightening all the screws I can see on the boat at least once a year like I do now

Love the zinc drywall anchors cause they will bite the hard back quickly and can re-use SS screws !!!

What are you surfing in that boat, I run 850 rears with kinetic vents so well burped , the 950 front well burped, stock and wedge and 500 lead, and we list extensively (4-6 gallons per hour depending on people load) with opposite side rear sac deflation
Have you been able to clean up your regular wave, I can make it decent size and length for push but not clean
If so let me know your set up
Hoping the lead I got to replace 3 150’s allows for some help cleaning up that wave
Goofy sick, will only get better with the lead front and back

_________________
14 A20, 850 rears with kinetic vents, front 950, stock plus wedge and 700 lead
P5 53” Ahi, Brigade 4’10” goofy asym, LF Happy pill 4’8”, LF Catalyst Nomad skate, HL wakeboard with old Murry boots


Top
 Profile  
 
 Post subject: Re: Engine Cover Hatch Screws Stripping
PostPosted: Sun Dec 10, 2017 7:51 pm 
Offline
Boater

Joined: Fri Nov 28, 2014 5:59 pm
Posts: 38
Location: East Berlin Pa
Another fantastic design by Malibu/Axis. Like everything else cheaply designed on an expensive boat. My 2015 A20 the screws came loose. Took the seat back out and drilled a hole large enough for a socket to fit directly opposite the hole for the strut. Put a nut and locking washer on and tightened down. Not coming out now and if it would loosen up have access to it.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 43 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


cron