It is currently Thu Mar 28, 2024 8:26 am

All times are UTC - 6 hours





Post new topic Reply to topic  [ 24 posts ]  Go to page 1, 2, 3  Next
Author Message
 Post subject: Replacing surfgate actuator
PostPosted: Sun Jun 25, 2017 1:35 pm 
Offline
Team Axis
User avatar

Joined: Mon Sep 23, 2013 4:01 pm
Posts: 1386
Location: Knoxville
It looks like I am going to have to replace one of my lenco tabs on my surfgate. Mine stopped working in the out position and won't retract back in. How hard is it to replace the actuator? It looks pretty simple. Any advice?

Edit as of 7/19/2017

I didn't enjoy paying $466 for the dealer to install a simple actuator on my surf gate so afterwards I did a little research. My 2014 Axis A22 uses the actuator below (15059-001). Check the link below on for your tab to ensure it isn't the fast model. Hopefully this helps others save a couple of bucks that can go towards gas and other repairs instead.

LENCO MARINE #15059-001 Lenco 102 Series Standard Actuator - 12V - 4-1/4" Stroke

https://www.amazon.com/Lenco-102-Standa ... B000YMWHMS

Also the 15129-001 is the Fast actuator. Mine used the 15059-001 though.

Link to Lenco's Actuator guide.

http://www.lencomarine.com/index.php/tr ... ory_id=324

Link to more info.
http://www.themalibucrew.com/index.php? ... actuators/


Last edited by dezul on Wed Jul 19, 2017 10:27 am, edited 2 times in total.

Top
 Profile  
 
 Post subject: Re: Replacing surfgate actuator
PostPosted: Mon Jun 26, 2017 5:25 am 
Offline
Team Axis
User avatar

Joined: Wed Sep 03, 2014 5:19 am
Posts: 457
Location: Mt. Washington, KY
Unpin the connector unbolt actuator and remove, it's easy. 3m 5200 around the harness where it enters transom

Sent from my SM-G900V using Tapatalk

_________________
2014 A24


Top
 Profile  
 
 Post subject: Re: Replacing surfgate actuator
PostPosted: Mon Jun 26, 2017 7:03 am 
Offline
Team Axis
User avatar

Joined: Mon Sep 23, 2013 4:01 pm
Posts: 1386
Location: Knoxville
dustinjean wrote:
Unpin the connector unbolt actuator and remove, it's easy. 3m 5200 around the harness where it enters transom

Sent from my SM-G900V using Tapatalk

That sounds easy enough and what I thought. I am guessing the actuator is proprietary to Axis and I must go through a dealer to get one?


Top
 Profile  
 
 Post subject: Re: Replacing surfgate actuator
PostPosted: Mon Jun 26, 2017 7:32 am 
Offline
Team Axis
User avatar

Joined: Wed Sep 03, 2014 5:19 am
Posts: 457
Location: Mt. Washington, KY
Not sure mine still worked but had to remove it for a different reason

Sent from my SM-G900V using Tapatalk

_________________
2014 A24


Top
 Profile  
 
 Post subject: Re: Replacing surfgate actuator
PostPosted: Mon Jun 26, 2017 7:47 am 
Offline
Team Axis

Joined: Sun Apr 05, 2015 4:41 pm
Posts: 255
Location: Ohio
So if the surfgate gets stuck open and computer reset doesn't fix the problem is there any way to manually get the gate to close and save a day in the water?

_________________
2015 T23


Top
 Profile  
 
 Post subject: Re: Replacing surfgate actuator
PostPosted: Mon Jun 26, 2017 7:50 am 
Offline
Team Axis
User avatar

Joined: Mon Sep 23, 2013 4:01 pm
Posts: 1386
Location: Knoxville
JohnnyBravo wrote:
So if the surfgate gets stuck open and computer reset doesn't fix the problem is there any way to manually get the gate to close and save a day in the water?

This happened to us. We just kept surfing that side. It made turning the boat tough. We idled back to the dock.


Top
 Profile  
 
 Post subject: Re: Replacing surfgate actuator
PostPosted: Mon Jun 26, 2017 9:20 am 
Offline
Team Axis
User avatar

Joined: Wed Sep 03, 2014 5:19 am
Posts: 457
Location: Mt. Washington, KY
Most actuators are threaded internally so if you unbolt it you can spin them back in unless something broke and put it in a bind

Sent from my SM-G900V using Tapatalk

_________________
2014 A24


Top
 Profile  
 
 Post subject: Re: Replacing surfgate actuator
PostPosted: Tue Jun 27, 2017 11:35 am 
Offline
Team Axis
User avatar

Joined: Mon Sep 23, 2013 4:01 pm
Posts: 1386
Location: Knoxville
dustinjean wrote:
Most actuators are threaded internally so if you unbolt it you can spin them back in unless something broke and put it in a bind

Sent from my SM-G900V using Tapatalk

Thanks for the tip. I did this action this morning and got the gate in now. It will get us out on the water till I can get a new one in. The bad part is I won't be able to get a replacement till July 11th. Apparently Malibu is shutdown for inventory and vacation till then.


Top
 Profile  
 
 Post subject: Re: Replacing surfgate actuator
PostPosted: Tue Jun 27, 2017 3:04 pm 
Offline
Team Axis
User avatar

Joined: Wed Sep 03, 2014 5:19 am
Posts: 457
Location: Mt. Washington, KY
dezul wrote:
dustinjean wrote:
Most actuators are threaded internally so if you unbolt it you can spin them back in unless something broke and put it in a bind

Sent from my SM-G900V using Tapatalk

Thanks for the tip. I did this action this morning and got the gate in now. It will get us out on the water till I can get a new one in. The bad part is I won't be able to get a replacement till July 11th. Apparently Malibu is shutdown for inventory and vacation till then.

Glad I could help, some of our equipment at work uses the same type of actuators with a major failure rate. So I've rebuild quite a few and had to adjust them in the field etc. Have you checked to make sure it has power at the pins back by the transom?

Sent from my SM-G900V using Tapatalk

_________________
2014 A24


Top
 Profile  
 
 Post subject: Re: Replacing surfgate actuator
PostPosted: Tue Jun 27, 2017 3:58 pm 
Offline
Team Axis
User avatar

Joined: Mon Sep 23, 2013 4:01 pm
Posts: 1386
Location: Knoxville
dustinjean wrote:
dezul wrote:
dustinjean wrote:
Most actuators are threaded internally so if you unbolt it you can spin them back in unless something broke and put it in a bind

Sent from my SM-G900V using Tapatalk

Thanks for the tip. I did this action this morning and got the gate in now. It will get us out on the water till I can get a new one in. The bad part is I won't be able to get a replacement till July 11th. Apparently Malibu is shutdown for inventory and vacation till then.

Glad I could help, some of our equipment at work uses the same type of actuators with a major failure rate. So I've rebuild quite a few and had to adjust them in the field etc. Have you checked to make sure it has power at the pins back by the transom?

Sent from my SM-G900V using Tapatalk

I haven't checked that. What do you suggest is the best way to do so? Multimeter while calibrating?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 24 posts ]  Go to page 1, 2, 3  Next

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 51 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: